Shop by line
Solid Wood Slat Acoustic Panels
Every slat is milled from one piece of solid walnut, oak or bamboo, front to back, on 9mm acoustic felt. No veneer and no core: cut a slat anywhere and the cut face looks just like the front.
Solid walnut Deep chocolate walnut, milled all the way through.
4 solid finishes
Compare Solid Series finishes
Solid American walnut, solid American oak and solid bamboo, each milled all the way through. All of them go up to 12 ft.
Solid American Walnut
13mm solid American walnut, milled all the way through. Low-satin finish, square-cut edges.
Shop Solid Walnut
Solid American Oak
13mm solid American oak, milled all the way through. Golden, with an open grain and a low-satin finish.
Shop Solid Oak
Solid Bamboo · Natural
Soft blonde solid bamboo. Light, calm and easy to pair.
Shop Solid Bamboo
Solid Bamboo · Medium Brown
Solid bamboo in a warm mid-brown. Cosy without going dark.
Shop Solid Bamboo
Why solid
Every slat is one piece of real material, front to back: no veneer skin, no MDF core, nothing wrapped. Cut a slat anywhere and the cut face looks just like the front.
Walnut and oak are sealed with 3 coats of low-satin polyurethane. Bamboo has a protective lacquer and is our most sustainable panel: it grows fast and regrows without replanting.
All Solid Series
Shop every Solid Series panel
Not sure on the color?
See it in your own light
Solid sample kit, $30. See the real wood and felt at home.
Get the sample kit
Not sure on the color?
See it in your own light
Solid sample kit, $30. See the real wood and felt at home.
Get the sample kit
Plan your wall
How many boxes do I need?
Pick your ceiling height and enter your wall width. We'll work out the boxes and price for each finish.
Volume discounts available on 9 and 12 ft panels.
Rounded up to whole boxes for one wall at full panel height. Add a box if you'll cut around windows or doors.
See the difference
Put them side by side, at home
Real walnut, oak and bamboo catch the light differently. Order the samples and compare them on your own wall.
Shop all samplesInstallation
How they go up
Walnut and oak go up the same way; bamboo has a different edge. Pick yours for the steps, or download the full guide as a PDF.
Acclimate, then adhesive, screws or both
- Acclimate 48–72 hours
Unbox and lay the panels flat on the floor of the room they're going in, out of the packaging and away from direct sun and heat. Don't stand them on end.
- Lead with the lip
Each panel has a bare felt lip on one edge and an overhanging slat on the other. Face every lip the way you're working.
- Fix it
Construction adhesive, or #6 or #8 screws (1.5–2″, trim-head) through the felt in the second gap in from each edge, rows no more than 24″ apart. Or both for extra hold. Save the flattest panels for the most visible spots.
- Lap the next panel
Lower each new panel so its overhanging slat drops over the last panel's felt lip, so the gap at the join matches the gaps between slats.
- If a slat bows
Put construction adhesive behind the panel and drive a trim-head screw through the felt gap right beside the bowed slat, into a stud or solid backing. Brace it while the adhesive cures.
- Corners
Hold the panel back 13mm at an outside corner and 6.5mm at an inside corner.
You'll need
- Drill / driver (cordless is best)
- #6 or #8 screws, 1.5–2″ (trim-head for a cleaner look)
- Construction adhesive, instead of or as well as screws
- 4 ft level or a laser, and a pencil
- Tape measure
- Stud finder or wall anchors
- Track, circular or hand saw with a fine-tooth blade
- Utility knife, for felt cuts
Cutting tips
- Cut to length with a track, circular or hand saw and a fine-tooth blade. Cut to width by slicing the felt in a gap with a utility knife: whole slats come away, no saw needed.
- Run painter's tape along the cut line before you saw, so the face doesn't splinter at the edge of the cut.
- Slats are stapled to the felt from the back every 10–13″. Line your cut up to miss the staples, and re-staple any slat that comes loose.
- Don't rip a slat lengthwise. Lift off a slat instead.
- At corners, hold the panel back rather than trimming the felt lip: 13mm at an outside corner, 6.5mm at an inside corner.
- Outlets and switches: a jigsaw or multi-tool through the slats, a utility knife through the felt.
Acclimate, then adhesive, screws or both
- Acclimate 48–72 hours
Unbox and lay the panels flat on the floor of the room they're going in, out of the packaging and away from direct sun and heat. Don't stand them on end.
- Lead with the lip
Each panel has a bare felt lip on one edge and an overhanging slat on the other. Face every lip the way you're working.
- Fix it
Construction adhesive, or #6 or #8 screws (1.5–2″, trim-head) through the felt gap. Or both for extra hold. Save the flattest panels for the most visible spots.
- Lap the next panel
Each panel has a 1″ felt lip on one edge; on the other, the last slat overhangs its felt by ½″. Lower each new panel so that overhang drops over the last panel's lip, and the gap at the join matches the gaps between slats.
You'll need
- Drill / driver (cordless is best)
- #6 or #8 screws, 1.5–2″ (trim-head for a cleaner look)
- Construction adhesive, instead of or as well as screws
- 4 ft level or a laser, and a pencil
- Tape measure
- Stud finder or wall anchors
- Track, circular or hand saw with a fine-tooth blade
- Utility knife, for felt cuts
Cutting tips
- Cut to length with a track, circular or hand saw and a fine-tooth blade. Cut to width by slicing the felt in a gap with a utility knife: whole slats come away, no saw needed.
- Run painter's tape along the cut line before you saw, so the face doesn't splinter at the edge of the cut.
- Don't rip a slat lengthwise. Take whole slats off instead.
- Outlets and switches: a jigsaw or multi-tool through the slats, a utility knife through the felt.
About this line
Good to know
The Solid series is the top of everything we make. Every slat is milled from one piece of real material, front to back — no veneer skin, no MDF core, nothing wrapped or faked. Cut a slat anywhere along its length and the cut face looks like the front face.
Three finishes, one construction. Solid American Walnut is the darkest — deep chocolate with sweeping grain. Solid American Oak is lighter and warmer, golden with open grain. Solid Bamboo in two distinct colors.














Ultralight
TrueWood Lite
Solid Oak & Walnut
Solid Bamboo
Paint-Ready




















